Best filament for 3D printed drones
The filament decides how heavy, stiff and heat-proof your 3D printed drone will be. Here is which material to use for the wing shells, the fuselage and the small strong parts of a fixed-wing or VTOL drone, with the numbers that matter.
The short answer
- Wings, fuselage and tail shells: lightweight foaming PLA (LW-PLA or Bambu PLA Aero), printed as a single thin wall.
- Strong small parts (motor mounts, servo frames, wing joiners, hinges): PETG, or PLA-CF / PETG-CF for extra stiffness.
- Hot climates or dark colours in full sun: ASA or PETG for the parts close to motors and batteries.
- Strength comes from carbon tubes, not from the plastic. Spars and booms carry the loads; the print gives the shape.
Filaments compared
| Filament | Density | Heat limit* | Best for | Notes |
|---|---|---|---|---|
| LW-PLA / PLA Aero | ≈ 0.5–0.8 g/cm³ (foamed) | ≈ 55 °C | Wing and fuselage shells | Half the weight of normal PLA. Needs tuned temperature and flow. |
| PLA | 1.24 g/cm³ | ≈ 55 °C | Small parts, test prints | Easy and stiff, but heavy for shells and soft in a hot car. |
| PETG | 1.27 g/cm³ | ≈ 75 °C | Mounts, hinges, joiners | Tougher than PLA: bends before it breaks in a hard landing. |
| PLA-CF / PETG-CF | ≈ 1.2–1.3 g/cm³ | 55–75 °C | Stiff brackets, landing gear | Stiffer, matte finish. Use a hardened nozzle. |
| ASA | 1.07 g/cm³ | ≈ 95 °C | Parts near motors, hot climates | UV-stable and heat-proof; needs an enclosed printer. |
| Nylon (PA-CF) | ≈ 1.1–1.2 g/cm³ | > 100 °C | High-load parts | Very strong, but must be kept dry. Not needed for most builds. |
*Approximate softening temperature. A dark wing in summer sun can pass 60 °C, so keep printed drones out of hot cars.
Why lightweight PLA for the shell
A drone's flight time depends mostly on its weight. LW-PLA foams in the nozzle, so one gram of plastic fills about twice the volume. Printed as a single 0.4–0.6 mm wall, a 1.8 m wing shell weighs far less than the same shape in normal PLA, and with carbon spars inside it is stiff enough for mapping flights with a 1 kg gimbal. See our LW-PLA print settings to tune temperature and flow.
What we use on our drones
| Drone | Shells | Small strong parts | Take-off weight |
|---|---|---|---|
| Cheel 1200 | LW-PLA / PLA Aero | PETG or PLA | ≈ 1.5 kg |
| Cheel 1800 | LW-PLA / PLA Aero | PETG | ≈ 4.1–4.6 kg |
| Cheel 1800 VTOL | LW-PLA / PLA Aero | PETG (boom mounts) | ≈ 5.9 kg |
| Koonj 1650 | LW-PLA / PLA Aero | PETG or PLA | ≈ 2.1 kg |
Each drone comes with a print guide that names the filament, walls and infill for every part, and a free assembly manual you can read on its page before you buy.
How much filament does a 3D printed drone need?
About 1–1.5 kg of LW-PLA for a 1.2–1.8 m wing, plus 100–300 g of PETG for the small parts. Larger VTOL drones use up to about 3 kg in total. Buy one more spool than you think: test prints and the occasional failed print add up.
Common mistakes
- Printing shells in normal PLA: the drone flies, but heavier, faster and for less time.
- Too much infill: wing shells need walls, not infill. Every gram costs flight time.
- Wet filament: LW-PLA and PETG take in moisture and print weak and stringy. Dry them before long prints.
- Leaving it in the sun: PLA-based parts can warp above about 55 °C.
Next step
Pick a drone from our 3D printed drones and estimate its endurance with the free flight time calculator. Building a VTOL? Read how to build a 3D printed VTOL drone.
Keep designing
Design Lab
Type in your own plane and get a scored analysis report: CG and neutral point, tail size, stall, L/D, flight time and wing strength, in 3D, with a PDF.
Open tool →Wing STL generator
Type in your wing and download print-ready STL sections with carbon tube channels, printed ribs, ailerons and a servo pocket.
Open tool →CG calculator
Balance point, neutral point and static margin for any RC plane, with a 3-view drawing and a battery-position helper.
Open tool →Flight time calculator
Endurance and range from weight, props and battery, with hover and cruise power.
Open tool →Wing loading calculator
Wing loading, stall and landing speed, and whether your weight is normal for your build.
Open tool →Battery pack calculator
Voltage, capacity, energy, weight and safe current for any S and P pack.
Open tool →