Shaheen 12003D printed tail-sitter VTOL drone
Any debit or credit card · no Payoneer account needed · Pakistan: bank, JazzCash, Easypaisa
The Shaheen is a 3D printed tail-sitter VTOL drone in the Cheel family. It stands on its tail, lifts straight up on two tractor motors, tips over and flies like a flying wing, then lands back on its four feet. No runway and no lift booms: the same two motors do the hover and the cruise, and two big elevons in the prop wash steer it. Named after the shaheen falcon.

- Wingspan
- 1200 mm
- Standing height
- 746 mm
- Take-off weight
- ≈ 2.13 kg
- Flight time
- ≈ 98 min*
- Hover
- 2 × 11" tractor props
- Controls
- 2 big elevons (42 % chord)
- Battery
- 4S2P 10 Ah / 4S3P 15 Ah
- Printed parts
- 26 · ≈ 0.88 kg
* Calculated with the 4S2P 10 Ah Li-ion pack at ≈ 47 km/h, including 2 minutes of hover. Plan missions with about 75 % for reserve.
Watch it come together
Every printed part and carbon rod in build order, then the Shaheen stands up on its tail, ready for take-off.
Where everything goes
Carbon spars, battery, autopilot, ESCs, servos and the wing lock, shown in place inside the see-through skin.

See-through view · click to enlarge.
Printed sections, nacelles and fins
Straight from the CAD: grey = light LW-PLA shell, blue = PETG nacelles and fins, black = carbon. The lines show where the printed sections join.

Front three-quarter · click to enlarge.

From above: the body pieces, the three wing sections per side and the big elevons · click to enlarge.

Exploded view: every printed part, carbon rod and joint · click to enlarge.
Dimensions, CG and battery
Every number comes straight from the 3D CAD: top, side and front views, battery and autopilot positions, CG and neutral point.

General arrangement · click to enlarge.
Numbers and setup
| Airframe | Value |
|---|---|
| Wingspan | 1200 mm (body + 2 plug-in wings) |
| Standing height | 746 mm, nose to feet |
| Wing | Cheel reflex airfoil 12 % · 24° sweep · −6° washout · 34 dm² · AR 4.23 |
| Mean chord (MAC) | 315 mm |
| Controls | 2 elevons, 42 % of the chord, 380 mm each, ~70 % in the prop wash |
| Yaw stability / feet | C-cut fins top + bottom (PETG + carbon rod) and 2 carbon wingtip legs, 4 TPU feet |
| Take-off weight | ≈ 2.13 kg (10 Ah) · ≈ 2.41 kg (15 Ah) |
| Stall | ≈ 38 km/h · best L/D 10.5 at ≈ 47 km/h |
| CG | 284 mm from the nose tip · aft limit 294 mm · neutral point 319 mm |
| Print bed | 256 × 256 mm (Bambu A1 class) |
| Electronics & setup | Value |
|---|---|
| Motors × 2 | 3115 class 900 KV · ≥ 2.1 kg thrust each · 11 × 5.5 props (1 CW + 1 CCW) |
| ESCs × 2 | 40 A, one inside each nacelle |
| Servos × 2 | 12 g metal gear, ≥ 4 kg·cm |
| Battery | 4S2P 21700 Li-ion 10 Ah brick (71 × 85 × 43 mm) or 4S3P 15 Ah |
| Hover power | ≈ 375 W / ≈ 25 A with 10 Ah |
| Autopilot | ArduPilot tail-sitter (Matek H743-WING / Pixhawk 6C mini) · ArduPilot tail-sitter guide |
| ArduPilot | Q_ENABLE 1 · Q_FRAME_CLASS 10 · Q_TAILSIT_ENABLE 1 · SERVO 77/78 elevons, 73/74 motors |
How long it flies
Calculated from the real CAD weights with 2 minutes of hover and hot-day air. Move the battery to the position in the table to get the CG right.
| Battery | Take-off weight | Battery centre (from nose) | Flight time |
|---|---|---|---|
| 4S2P P50B Li-ion 10 Ah | 2.13 kg | 117 mm | ≈ 98 min |
| 4S3P P50B Li-ion 15 Ah | 2.41 kg | 171 mm | ≈ 130 min |
How it flies, on paper
Computed on the real CAD geometry: a vortex-lattice model of the wing, NeuralFoil airfoil data (trained on XFOIL) and a drag build-up of every part. Real numbers depend on your build, battery and wind.

Lift curve, drag polar, pitch stability and lift-to-drag versus speed · click to enlarge

Lift along the span and where the wing stalls first · click to enlarge

Pressure on the reflexed airfoil in cruise · click to enlarge

Where the drag comes from, and flight time versus speed · click to enlarge
Stable without a tail
Reflexed Cheel airfoil and 24° sweep: neutral point 319 mm from the nose, CG 284 mm, static margin 11 %.
Soft stall, easy transition
−6° washout makes the inner wing stall first, so the big elevons keep working while it tips over from hover to flight. Span efficiency ≈ 0.929.
Clean for a VTOL
No lift booms, no stopped props: the tail-sitter parts make only about a fifth of the cruise drag. Best L/D 10.5.
Why a tail-sitter
The same two motors lift it in hover and pull it in flight. Fewer motors, less weight and less drag than a 4 + 1 quad-plane of the same size.
Print settings and carbon
Every printed part fits a 256 × 256 mm bed and comes already rotated for printing. Light LW-PLA for the shell, PETG where it carries motor and landing loads.
| Parts | Filament | Settings |
|---|---|---|
| Wings, elevons, body, hatches | LW-PLA | 2 walls, 0 % infill: inner slots print as ribs and spar webs |
| Nacelles (motor + ESC) | PETG | 3 walls, 15 % gyroid |
| C-cut fins (landing feet) | PETG | 3 walls, 10 % gyroid |
| 4 feet | TPU 95A | 3 walls, 30 % |
| Qty | Carbon | Length (mm) | Use |
|---|---|---|---|
| 2 | Tube 10 × 8 | 648 | Main spars (cross in the body) |
| 2 | Tube 6 × 4 | 356 | Rear spars |
| 2 | Rod Ø5 | 104 | Rear pins |
| 2 | Rod Ø4 | 243 | Wingtip legs |
| 2 | Rod Ø3 | 173 | Fin rods |
| 2 | Rod Ø3 | 60 | Elevon joiners |
How the parts join
Wing to body
Each wing slides onto the body on its own 10 mm carbon main spar; the two spars cross inside the body. A 5 mm rear pin stops twist and one M4 nylon bolt from below locks the wing.
Nacelles
Each PETG nacelle wraps the wing leading edge and is bolted through the wing with 2 × M3. The ESC sits inside, cooled by the prop wash.
Fins
The C-cut fins plug into slots in the rear body with a tongue and a 3 mm carbon rod. They keep the wing straight in flight and are two of the four feet.
Big elevons
Two printed pieces per side on a 3 mm carbon joiner, one 12 g metal-gear servo each. In hover they steer the drone in the prop wash.
What you get
Download from My account after payment. Files are for personal use; print and fly as many as you like.
- 26 print-ready STL files, already rotated for a Bambu Lab 256 mm bed (A1 / P1S / P1P / X1C)
- The same parts in assembly position + all carbon parts
- Whole-drone assembly (.3mf / .glb) to check every part in 3D
- Step-by-step assembly manual (PDF, 17 pages) with a 3D picture for every step, ArduPilot tail-sitter setup and first-flight checklist
- General-arrangement drawing, x-ray, studio renders and the aero report
Shaheen 1200 STL files
Print it on any Bambu Lab printer, add carbon rods and electronics, fly it with ArduPilot.
Any debit or credit card · no Payoneer account needed · Pakistan: bank, JazzCash, Easypaisa
