LayerWings Sign in
Home / Planes / Cheel 1800
Drone mapping and survey wing with a gimbal module · 1800 mm

Cheel 18003D printed mapping drone

$49 $59 launch price

Any debit or credit card · no Payoneer account needed · Pakistan: bank, JazzCash, Easypaisa

See the smaller Cheel 1200 →

A 3D printed 1.8 m mapping drone: a blended flying wing for drone mapping, aerial survey and inspection. A plug-and-play belly module carries a zoom + day/night gimbal up to 1 kg, protected by two skids. Fly about an hour with the camera on a 6S2P Li-ion pack, or 90 minutes on 6S3P. Hand or bungee launch, belly landing, and every part prints on a normal Bambu Lab printer. Also available: the Cheel 1800 VTOL, the same wing with vertical take-off and landing.

Wingspan
1800 mm
Payload
gimbal up to 1 kg
Wing area
63.9 dm²
Take-off weight
≈ 4.1–4.6 kg
Flight time
≈ 63–90 min*
Cruise
65 km/h
Launch
hand or bungee
CG
462 mm from the nose

* Calculated at 65 km/h cruise with the gimbal (6S2P / 6S3P). Plan missions with about 75 % for reserve.

360° view

See the Cheel 1800 from every side

Drone mapping & survey

Made for the job

Orthophotos, 3D models, crop and land survey, power line and pipeline inspection, search and rescue: a long-endurance wing with a protected camera bay.

Plug-and-play gimbal module

The gimbal bolts to a deck inside one PETG belly module with two skids. Six thumb screws, about one minute to swap. No camera today? Fit the flat cover plate and move the battery forward.

Skids protect the camera

The skids sit 8 mm lower than the camera ball, so the wing lands on them, never on the lens. Set the gimbal to look backwards before landing.

Carbon box structure

14 x 12 carbon main spars run straight into the body and cross there; 8 x 6 rear spars, printed shear webs and diagonal ribs make every wing piece a stiff box.

Fits a normal printer

Every wing section is printed as a front and a rear piece, glued on a flat face, so all 34 parts fit a 256 mm Bambu Lab bed.

Mapping ready

Long, efficient cruise for photogrammetry, ArduPilot survey missions with camera trigger, room for PPK / RTK GPS in the rear hatch.

Plug-in wings

Slide each wing on along its spar, push the 6 mm rear pin home, lock with one M5 nylon bolt. Packs flat for transport.

Inside

Where everything goes

Carbon spars, battery, autopilot, servos, gimbal module and skids, shown in place.

Cheel 1800 x-ray

X-ray of the Cheel 1800 with the gimbal module · click to enlarge

Printed parts

34 printed parts: each colour is one print on a 256 mm bed · click to enlarge

2D drawing · mm

Dimensions and CG

Top, side and front views from the CAD. The red dashed line is the balance point.

Cheel 1800 dimensions

All main dimensions in mm · click to enlarge

Cheel 1800 general arrangement

General arrangement · dotted lines are the printed piece joints · click to enlarge

Aerodynamic report

How it flies, on paper

Computed on the real CAD geometry: a swept vortex-lattice model of the blended wing, NeuralFoil airfoil data (trained on XFOIL) and a part-by-part drag build-up, with the gimbal and the VTOL kit included. Real numbers depend on your build, battery and wind.

Cheel 1800: Lift curve, drag polar, pitch stability, L/D versus speed

Lift curve, drag polar, pitch stability, L/D versus speed · click to enlarge

Cheel 1800: Lift along the span and stall map on the planform

Lift along the span and stall map on the planform · click to enlarge

Cheel 1800: Pressure on the body and wing airfoil sections

Pressure on the body and wing airfoil sections · click to enlarge

Cheel 1800: Drag build-up and flight time versus speed

Drag build-up and flight time versus speed · click to enlarge

Specifications

Numbers and setup

AirframeValue
LayoutBlended wing-body flying wing, winglets, pusher
Wingspan / length1800 mm / ≈ 975 mm
Wing area / MAC63.9 dm² / 434 mm
Sweep / washout30° leading edge / −6° at the tip
AirfoilReflexed (self-stable), thick lifting body → 12 % wing root → 10 % tip
CG462 mm behind the nose tip · neutral point 497 mm · static margin 8 %
Gimbal + 6S2P 10 Ah≈ 4.14 kg · stall ≈ 39 km/h · ≈ 63 min
Gimbal + 6S3P 15 Ah≈ 4.58 kg · stall ≈ 41 km/h · ≈ 90 min
No camera (cover plate) + 6S3P≈ 3.49 kg · ≈ 116 min
Electronics & payloadValue
Pusher4120 / 3520 class ≈ 450 KV, 14 x 8 folding prop, 80 A ESC
Battery6S2P or 6S3P 21700 Li-ion (Molicel P50B / P45B), flat pack under the spars
PayloadZoom + day/night gimbal up to 1 kg (ball ≤ 120 mm) or a mapping camera
Servos2 metal-gear wing servos (12 mm class)
AutopilotArduPilot (Pixhawk / Matek H743) · camera trigger · PPK / RTK GPS ready · ArduPilot elevon setup
Launch / landingHand or bungee launch, belly landing on the skids
Bambu Lab ready · 256 mm bed

Filament and print list

Every file comes rotated, flat and centred for Bambu Lab A1, P1S, P1P and X1C. Checked: fits the bed with at least 8 mm to spare, watertight, no supports on the wings or body. The A1 mini (180 mm) is too small.

FilamentAmountUsed for
LW-PLA / Bambu PLA Aero≈ 1143 g (about 1.5 spools)Wings, body, hatches, elevons, winglets · 2 walls, 0 % infill
PETG≈ 169 gGimbal module (with skids) and cover plate
PartOn the bed (mm)FilamentHow it printsSupports≈ g
BODY-1L130 x 137 x 214LW-PLA2 walls, 0 % infill, standing on the rear joint face, nose upnone25 g
BODY-1R130 x 137 x 214LW-PLA2 walls, 0 % infill, standing on the rear joint face, nose upnone25 g
BODY-2L215 x 154 x 227LW-PLA2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls)none58 g
BODY-2R215 x 154 x 227LW-PLA2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls)none58 g
BODY-3L215 x 137 x 230LW-PLA2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls)none53 g
BODY-3R215 x 137 x 230LW-PLA2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls)none53 g
BODY-4L193 x 193 x 225LW-PLA2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls)none33 g
BODY-4R193 x 193 x 225LW-PLA2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls)none33 g
COVER-PLATE179 x 163 x 54PETG3 walls, 20 % infill, outer face downtree supports (build plate only)44 g
ELEVON-L1106 x 106 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone15 g
ELEVON-L299 x 99 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone13 g
ELEVON-R1106 x 106 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone15 g
ELEVON-R299 x 99 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone13 g
GIMBAL-MODULE179 x 163 x 163PETG4 walls, 25 % gyroid, deck face down (upside down)tree supports under the plate + skids125 g
HATCH-H1130 x 130 x 170LW-PLA2 walls, 0 % infill, standing on its front edgenone19 g
HATCH-H2118 x 118 x 160LW-PLA2 walls, 0 % infill, standing on its front edgenone12 g
WING-L1A176 x 176 x 155LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone43 g
WING-L1F186 x 186 x 155LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone60 g
WING-L2A154 x 154 x 160LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone36 g
WING-L2F175 x 174 x 160LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone51 g
WING-L3A116 x 117 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone25 g
WING-L3F170 x 169 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone46 g
WING-L4A144 x 144 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone23 g
WING-L4F156 x 156 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone38 g
WING-R1A176 x 176 x 155LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone43 g
WING-R1F186 x 186 x 155LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone60 g
WING-R2A154 x 154 x 160LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone36 g
WING-R2F174 x 175 x 160LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone51 g
WING-R3A117 x 116 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone25 g
WING-R3F169 x 170 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone46 g
WING-R4A144 x 144 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone23 g
WING-R4F156 x 156 x 180LW-PLA2 walls, 0 % infill, 0.6 mm skin, standing on the inboard facenone38 g
WINGLET-L180 x 180 x 204LW-PLA2 walls, 0 % infill, standing on the basenone37 g
WINGLET-R180 x 180 x 204LW-PLA2 walls, 0 % infill, standing on the basenone37 g
Buy separately

Carbon and hardware

QtyPartLengthWhere
2Tube 14 x 12≈ 1070 mmMain spars (cross inside the body)
2Tube 8 x 6≈ 545 mmRear spars
2Rod 6 mm≈ 170 mmRear pins
2Rod 3 mm60 mmElevon joiners
4Rod 3 mm25 mmWinglet pins
2M5 nylon bolt + insert30 mmWing lock
6M4 thumb screw + insert12 mmGimbal module / cover plate
≈ 401.75 mm filament20 mmAlignment pins
8Magnets 6 x 3Hatches
Assembly

How it goes together

  1. Glue each wing section's front and rear piece (2 filament pins), then glue the 8 body pieces.
  2. Thread the 4 sections of each wing onto the 14 x 12 main spar and the 8 x 6 rear spar, glue with slow epoxy.
  3. Join the elevon pieces with a 3 mm rod, hinge them, fit the wing servos; glue the winglets on their pins.
  4. Slide the wings on along the spars, push the 6 mm rear pins home, lock with the M5 bolts.
  5. Bolt your gimbal to the module, fit it with the 6 thumb screws. Balance at 462 mm from the nose (battery position from the manual).
Free download · no sign-up

Assembly manual

See exactly how the Cheel 1800 goes together before you buy: parts map, print list, a 3D exploded picture for every step, carbon cut lengths, wiring, setup and a first-flight checklist.

Cheel 1800 assembly manual: cover, parts map and a step page
The download

What you get

Download from My account after payment. Files are for personal use; you may print and fly as many as you like.

  • 34 print-ready STL files, pre-oriented for Bambu Lab A1 / P1S / P1P / X1C (256 mm bed)
  • Step-by-step assembly manual (PDF, 20 pages): a 3D exploded picture for every step
  • Print guide with settings, supports and grams per part
  • All parts in assembly position + carbon tubes (STL)
  • Whole-plane assembly (.3mf / .glb), with gimbal module and with cover plate
  • PDF build manual (assembly, gimbal module, CG and battery positions, first flight, mapping missions)
  • PDF print guide and PDF dimensions sheet
  • Dimensions drawing, x-ray and parts layout pictures
  • Free updates by email
New · mapping & survey

Cheel 1800 STL files

1.8 m flying wing with a plug-and-play gimbal module. Print it on any Bambu Lab printer, add carbon and electronics, fly survey missions with ArduPilot.

$49 $59 launch price

Any debit or credit card · no Payoneer account needed · Pakistan: bank, JazzCash, Easypaisa

Weigh your parts and check the CG before the first flight.