Cheel 1800 VTOL3D printed VTOL mapping drone
Any debit or credit card · no Payoneer account needed · Pakistan: bank, JazzCash, Easypaisa
A 3D printed VTOL mapping drone: the Cheel 1800 survey wing with a bolt-on 4 + 1 VTOL kit: two carbon booms and four 15" lift props. It takes off and lands vertically, then flies forward on the pusher. Built for drone mapping and survey from small sites with no runway: zoom + day/night gimbal up to 1 kg, about 55 minutes on 6S3P Li-ion, and every part prints on a normal Bambu Lab printer.

- Wingspan
- 1800 mm
- Take-off
- vertical (4 + 1)
- Payload
- gimbal up to 1 kg
- Take-off weight
- ≈ 5.9 kg
- Flight time
- ≈ 55 min*
- Cruise
- 68 km/h
- Lift props
- 4 x 15"
- CG
- 462 mm from the nose
* With the gimbal and a 6S3P pack, incl. 2 minutes of hover. Plan missions with about 75 % for reserve.
See the Cheel 1800 VTOL from every side
Made for the job
Take off from a field corner, a rooftop or a clearing, fly a long survey mission like a plane, land vertically next to you.
Vertical take-off and landing
Four 15" lift props on two carbon booms lift the 5.9 kg wing straight up. It transitions to forward flight on the pusher and lands vertically: no runway, no launcher, no belly landing.
Plug-and-play gimbal module
The gimbal bolts to a deck inside one PETG belly module with two skids. Six thumb screws, about one minute to swap. No camera today? Fit the flat cover plate and move the battery forward.
Skids protect the camera
The skids sit 8 mm lower than the camera ball, so the wing lands on them, never on the lens. Set the gimbal to look backwards before landing.
Carbon box structure
14 x 12 carbon main spars run straight into the body and cross there; 8 x 6 rear spars, printed shear webs and diagonal ribs make every wing piece a stiff box.
Fits a normal printer
Every wing section is printed as a front and a rear piece, glued on a flat face, so all 34 parts fit a 256 mm Bambu Lab bed.
Mapping ready
Long, efficient cruise for photogrammetry, ArduPilot survey missions with camera trigger, room for PPK / RTK GPS in the rear hatch.
Bolt-on VTOL kit
Each boom is held by a PETG pylon bolted through the wing with two M4 bolts, clear of the carbon spars. Take the kit off and the same airframe flies as the hand-launched Cheel 1800.
Where everything goes
Carbon spars, battery, autopilot, servos, gimbal module and skids, shown in place.

From below: booms, lift motors, legs and the gimbal module · click to enlarge

Airframe x-ray (same as the Cheel 1800): carbon spars, battery, autopilot, gimbal · click to enlarge
Dimensions and CG
Top, side and front views from the CAD. The red dashed line is the balance point.

All main dimensions in mm · click to enlarge

General arrangement · dotted lines are the printed piece joints · click to enlarge
How it flies, on paper
Computed on the real CAD geometry: a swept vortex-lattice model of the blended wing, NeuralFoil airfoil data (trained on XFOIL) and a part-by-part drag build-up, with the gimbal and the VTOL kit included. Real numbers depend on your build, battery and wind.

Lift curve, drag polar, pitch stability, L/D versus speed · click to enlarge

Lift along the span and stall map on the planform · click to enlarge

Pressure on the body and wing airfoil sections · click to enlarge

Drag build-up and flight time versus speed · click to enlarge
Numbers and setup
| Airframe | Value |
|---|---|
| Layout | Blended wing-body flying wing, winglets, pusher |
| Wingspan / length | 1800 mm / ≈ 975 mm |
| Wing area / MAC | 63.9 dm² / 434 mm |
| Sweep / washout | 30° leading edge / −6° at the tip |
| Airfoil | Reflexed (self-stable), thick lifting body → 12 % wing root → 10 % tip |
| CG | 462 mm behind the nose tip · neutral point 497 mm · static margin 8 % |
| VTOL booms | 20 x 18 carbon, 1088 mm, at ±420 mm · lift motors at CG ± 514 mm |
| Gimbal + 6S3P 15 Ah | ≈ 5.90 kg · hover ≈ 778 W · ≈ 55 min |
| Gimbal + 6S2P 10 Ah | ≈ 5.46 kg · hover ≈ 692 W · ≈ 37 min |
| No camera (cover plate) + 6S3P | ≈ 4.88 kg · ≈ 65 min |
| Electronics & payload | Value |
|---|---|
| Pusher | 4120 / 3520 class ≈ 450 KV, 14 x 8 folding prop, 80 A ESC |
| Battery | 6S2P or 6S3P 21700 Li-ion (Molicel P50B / P45B), flat pack under the spars |
| Payload | Zoom + day/night gimbal up to 1 kg (ball ≤ 120 mm) or a mapping camera |
| Servos | 2 metal-gear wing servos (12 mm class) |
| Autopilot | ArduPilot QuadPlane (Pixhawk / Matek H743) · Q_FRAME_CLASS 1, Q_FRAME_TYPE 1 · camera trigger · PPK / RTK ready · ArduPilot QuadPlane guide |
| Lift motors | 4 x 4114 / 4120 ≈ 400 KV (6S), 15" props, 40–50 A ESCs · 2.65 kg thrust each needed |
| Take-off / landing | Vertical, on 4 legs (12 mm lower than the gimbal skids) |
Filament and print list
Every file comes rotated, flat and centred for Bambu Lab A1, P1S, P1P and X1C. Checked: fits the bed with at least 8 mm to spare, watertight, no supports on the wings or body. The A1 mini (180 mm) is too small.
| Filament | Amount | Used for |
|---|---|---|
| LW-PLA / Bambu PLA Aero | ≈ 1143 g (about 1.5 spools) | Wings, body, hatches, elevons, winglets · 2 walls, 0 % infill |
| PETG / PETG-CF | ≈ 456 g | Pylons, motor mounts, gimbal module, cover plate |
| TPU 95A | ≈ 16 g | Feet |
| Part | On the bed (mm) | Filament | How it prints | Supports | ≈ g |
|---|---|---|---|---|---|
| BODY-1L | 130 x 137 x 214 | LW-PLA | 2 walls, 0 % infill, standing on the rear joint face, nose up | none | 25 g |
| BODY-1R | 130 x 137 x 214 | LW-PLA | 2 walls, 0 % infill, standing on the rear joint face, nose up | none | 25 g |
| BODY-2L | 215 x 154 x 227 | LW-PLA | 2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls) | none | 58 g |
| BODY-2R | 215 x 154 x 227 | LW-PLA | 2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls) | none | 58 g |
| BODY-3L | 215 x 137 x 230 | LW-PLA | 2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls) | none | 53 g |
| BODY-3R | 215 x 137 x 230 | LW-PLA | 2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls) | none | 53 g |
| BODY-4L | 193 x 193 x 225 | LW-PLA | 2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls) | none | 33 g |
| BODY-4R | 193 x 193 x 225 | LW-PLA | 2 walls, 0 % infill, lying on the flat centre split face (tail block: 3 walls) | none | 33 g |
| COVER-PLATE | 179 x 163 x 54 | PETG | 3 walls, 20 % infill, outer face down | tree supports (build plate only) | 49 g |
| ELEVON-L1 | 106 x 106 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 15 g |
| ELEVON-L2 | 99 x 99 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 13 g |
| ELEVON-R1 | 106 x 106 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 15 g |
| ELEVON-R2 | 99 x 99 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 13 g |
| FOOT-LF | 24 x 24 x 16 | TPU 95A | 3 walls, 30 % infill | none | 4 g |
| FOOT-LR | 24 x 24 x 16 | TPU 95A | 3 walls, 30 % infill | none | 4 g |
| FOOT-RF | 24 x 24 x 16 | TPU 95A | 3 walls, 30 % infill | none | 4 g |
| FOOT-RR | 24 x 24 x 16 | TPU 95A | 3 walls, 30 % infill | none | 4 g |
| GIMBAL-MODULE | 179 x 163 x 163 | PETG | 4 walls, 25 % gyroid, deck face down (upside down) | tree supports under the plate + skids | 139 g |
| GIMBAL-MODULE-NOSKID | 179 x 163 x 122 | PETG | 4 walls, 25 % gyroid, deck face down (upside down) | tree supports under the plate + skids | 68 g |
| HATCH-H1 | 130 x 130 x 170 | LW-PLA | 2 walls, 0 % infill, standing on its front edge | none | 19 g |
| HATCH-H2 | 118 x 118 x 160 | LW-PLA | 2 walls, 0 % infill, standing on its front edge | none | 12 g |
| MOTORMOUNT-LF | 48 x 48 x 47 | PETG | 5 walls, 60 % gyroid, motor face down | build plate only | 13 g |
| MOTORMOUNT-LR | 48 x 48 x 47 | PETG | 5 walls, 60 % gyroid, motor face down | build plate only | 13 g |
| MOTORMOUNT-RF | 48 x 48 x 47 | PETG | 5 walls, 60 % gyroid, motor face down | build plate only | 13 g |
| MOTORMOUNT-RR | 48 x 48 x 47 | PETG | 5 walls, 60 % gyroid, motor face down | build plate only | 13 g |
| PYLON-L | 150 x 150 x 36 | PETG | 5 walls, 40 % gyroid, flat bottom down | none | 74 g |
| PYLON-R | 150 x 150 x 36 | PETG | 5 walls, 40 % gyroid, flat bottom down | none | 74 g |
| WING-L1A | 176 x 176 x 155 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 43 g |
| WING-L1F | 186 x 186 x 155 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 60 g |
| WING-L2A | 154 x 154 x 160 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 36 g |
| WING-L2F | 175 x 174 x 160 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 51 g |
| WING-L3A | 116 x 117 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 25 g |
| WING-L3F | 170 x 169 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 46 g |
| WING-L4A | 144 x 144 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 23 g |
| WING-L4F | 156 x 156 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 38 g |
| WING-R1A | 176 x 176 x 155 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 43 g |
| WING-R1F | 186 x 186 x 155 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 60 g |
| WING-R2A | 154 x 154 x 160 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 36 g |
| WING-R2F | 174 x 175 x 160 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 51 g |
| WING-R3A | 117 x 116 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 25 g |
| WING-R3F | 169 x 170 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 46 g |
| WING-R4A | 144 x 144 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 23 g |
| WING-R4F | 156 x 156 x 180 | LW-PLA | 2 walls, 0 % infill, 0.6 mm skin, standing on the inboard face | none | 38 g |
| WINGLET-L | 180 x 180 x 204 | LW-PLA | 2 walls, 0 % infill, standing on the base | none | 37 g |
| WINGLET-R | 180 x 180 x 204 | LW-PLA | 2 walls, 0 % infill, standing on the base | none | 37 g |
Carbon and hardware
| Qty | Part | Length | Where |
|---|---|---|---|
| 2 | Tube 14 x 12 | ≈ 1070 mm | Main spars (cross inside the body) |
| 2 | Tube 8 x 6 | ≈ 545 mm | Rear spars |
| 2 | Rod 6 mm | ≈ 170 mm | Rear pins |
| 2 | Rod 3 mm | 60 mm | Elevon joiners |
| 4 | Rod 3 mm | 25 mm | Winglet pins |
| 2 | M5 nylon bolt + insert | 30 mm | Wing lock |
| 6 | M4 thumb screw + insert | 12 mm | Gimbal module / cover plate |
| ≈ 40 | 1.75 mm filament | 20 mm | Alignment pins |
| 8 | Magnets 6 x 3 | Hatches | |
| 2 | Tube 20 x 18 | 1088 mm | VTOL booms |
| 4 | Rod 8 mm | ≈ 50 mm | Legs |
| 4 | M4 bolt + insert | 40 mm | Pylons through the wing |
| 4 | M3 bolt + nut | 30 mm | Boom clamps |
How it goes together
- Glue each wing section's front and rear piece (2 filament pins), then glue the 8 body pieces.
- Thread the 4 sections of each wing onto the 14 x 12 main spar and the 8 x 6 rear spar, glue with slow epoxy.
- Join the elevon pieces with a 3 mm rod, hinge them, fit the wing servos; glue the winglets on their pins.
- Slide the wings on along the spars, push the 6 mm rear pins home, lock with the M5 bolts.
- Bolt the pylons under the wing (2 M4 each), slide in the booms, fit motor mounts, legs and feet.
- Bolt your gimbal to the module, fit it with the 6 thumb screws. Balance at 462 mm from the nose; the lift motors are centred on it.
What you get
Download from My account after payment. Files are for personal use; you may print and fly as many as you like.
- 45 print-ready STL files incl. the VTOL kit, pre-oriented for Bambu Lab A1 / P1S / P1P / X1C (256 mm bed)
- Step-by-step assembly manual (PDF, 23 pages): a 3D exploded picture for every step
- Print guide with settings, supports and grams per part
- All parts in assembly position + carbon tubes and booms (STL)
- Whole VTOL assembly (.3mf / .glb)
- ArduPilot QuadPlane setup notes
- PDF build manual (assembly, gimbal module, CG and battery positions, first flight, mapping missions)
- PDF print guide and PDF dimensions sheet
- Dimensions drawing, x-ray and parts layout pictures
- Free updates by email
Cheel 1800 VTOL STL files
The full Cheel 1800 airframe plus the VTOL kit. Print it on any Bambu Lab printer, add carbon and electronics, fly survey missions with ArduPilot QuadPlane.
Any debit or credit card · no Payoneer account needed · Pakistan: bank, JazzCash, Easypaisa
Weigh your parts and check the CG before the first flight.
