How to build a 3D printed VTOL drone
A VTOL drone takes off and lands straight up like a multicopter, then flies forward on a wing like a plane. This guide walks through building a 3D printed quad-plane (4 lift motors + 1 pusher) from print to first hover, using our Cheel 1200 VTOL and Cheel 1800 VTOL as examples.
1. Choose the size
Bigger wings fly longer and carry more, but need more carbon, bigger props and more battery. A 1.2 m VTOL wing is a good first build for FPV and small cameras. A 1.8 m VTOL carries a 1 kg zoom or day/night gimbal for mapping and inspection. As a rule, the lift motors together should give at least 1.8 times the take-off weight in thrust.
2. Print the parts
- Printer: a 256 mm bed (Bambu Lab A1, P1S, P1P, X1C). Our files are split and pre-oriented for it.
- Airframe: LW-PLA or Bambu PLA Aero, 2 walls and 0 % infill, so the shell stays light. See our LW-PLA settings.
- Load-carrying parts: boom pylons and motor mounts in PETG or PETG-CF with 5 walls and 40–60 % infill. Landing feet in TPU.
3. Build the wing around carbon
The printed shell gives the shape, the carbon carries the loads. Slide the wing sections onto a main carbon spar and a smaller rear spar, fill the channels with slow epoxy and glue the section faces. On a VTOL the lift booms hang under the wing, so the spar must also carry the hover loads: never skip or shorten it.
4. Add the VTOL kit
- Bolt a printed pylon under each wing, through the wing into heat-set inserts.
- Clamp a carbon boom (16–20 mm) in each pylon, the same length in front and behind the centre of gravity.
- Fit motor mounts on the boom ends and check all four motor plates are level: tilted motors make the hover drift.
- Front-right and rear-left props turn counter-clockwise, front-left and rear-right clockwise (ArduPilot quad X).
5. Electronics and wiring
A typical setup: one pusher motor and ESC, four lift motors and ESCs (or a 4-in-1 board), two elevon servos, a GPS with compass, a receiver and a flight controller running ArduPilot (Pixhawk or Matek H743 class). Power the lift ESCs straight from the battery with thick wire; hover takes several hundred watts. A separate 5–6 V BEC for servos keeps the controller safe.
6. ArduPilot QuadPlane setup
Q_ENABLE = 1,Q_FRAME_CLASS = 1(quad),Q_FRAME_TYPE = 1(X).- Lift motors on outputs 5–8 (functions 33–36), elevons on 77 / 78, pusher on 70.
- Run the motor test with props off to check the order and direction, then calibrate accelerometer, compass and radio.
The full parameter list is in the ArduPilot QuadPlane guide.
7. Balance and first hover
Balance the drone at the CG mark with the battery and payload fitted; the lift motors sit equally far in front and behind it. Use our flying wing CG calculator for your own designs. First hover: QHOVER at 1 m in calm wind, then short hops, then a transition to forward flight at a safe height. Keep the first flight checklist at hand.
Keep designing
Design Lab
Type in your own plane and get a scored analysis report: CG and neutral point, tail size, stall, L/D, flight time and wing strength, in 3D, with a PDF.
Open tool →Wing STL generator
Type in your wing and download print-ready STL sections with carbon tube channels, printed ribs, ailerons and a servo pocket.
Open tool →RC plane CG calculator
Center of gravity, neutral point and static margin for any RC plane or model airplane, with a 3-view drawing and a battery-position helper.
Open tool →Flight time calculator
Endurance and range from weight, props and battery, with hover and cruise power.
Open tool →Wing loading calculator
Wing loading, stall and landing speed, and whether your weight is normal for your build.
Open tool →Battery pack calculator
Voltage, capacity, energy, weight and safe current for any S and P pack.
Open tool →